Winter is finally here

Here it is, almost February and winter is just arriving.  Sure, we have had a few cold days, but no rain to speak of.  Now it is starting.  So now the question comes up, Will we have a late winter (that goes into the spring)? or will we have a short winter?  Now that work is picking back up, planning becomes more important.

No question that the painting trade has changed.  New construction, notably housing, went from “full Throttle” to “dead in the water”.  Repaint and maintenance went from “really busy” to “hardly any”.  This fall has shown both to start reviving.  New projects won’t get close to the 2006 pace for a long time, if ever.  Repaint and maintenance is now on it’s knees; from flat on it’s face. I am seeing projects that needed to be done 4 years ago, starting up.  Because of this stall, the maintenance work has degenerated from maintenance to repair.  So, the extra cost of waiting to be done, will slow some of it’s recovery.  Ironic, isn’t it? But deferring maintenance has always cost more.

Thinking of deferring costing more….  This applies to airless rigs as well.  If your pump is leaking at the piston, not repairing it right away jeopardizes the piston.  This can easily double the cost of repair.  So as soon as you notice leakage, schedule the machine to be repaired.  This will allow you to repair the machine at a known time, rather than causing a panic when it completely fails during the middle of a project.

Additional Recipes

In opening this today, I realized that I have neglected to post the additional flavors that we have.  So here is that post

11/26/2010

We spent The holidays in Arizona.  We had a ShapeWay tasting and came away with 2 new flavors.  These were acquired by the tried and true “hit and miss” method…

17'.  the “Kat”  8: 8 oz Non-Fat Milk, 1 scoop S/W, 1 tablespoon unsweetened chocolate, 1 tablespoon peanut butter, 1.5oz ZILLA.

18. the “Larry” 8: 8 oz NF Milk, 1 scoop S/W, 1/2 banana, 1 tablespoon unsweetened chocolate, 1.5 oz ZILLA.

Buyers Beware

I am seeing quite a few recently purchased, used pumps coming in.  There are a lot of used pumps on the market these days, due to the downturn in the painting industry.  Most of these pumps haven’t been run for years.  Some were broken when they were stored and some were in working order.  Remember that storing a pump is the same as storing a car.  Taken out of storage, both will need work.

Take the car, for example.  If it wasn’t stored properly, you will need a battery, air in tires as a minimum as rubber stored under weight breaks down, so maybe all 4 tires.  If the engine wasn’t stored dry, you will need to drain, clean and/or rebuild the fuel delivery system and completely drain, flush and refill the engine oil and cooling systems.

An airless is quite the same.  At a minimum; figure filters, screens and a complete repack of the fluid section.  If it wasn’t stored properly, then you may need a piston rod and/or sleeve.  If it had any residue of paint or colored water in it, the prime valve may not open or close off completely.  And if it is a gas powered pump, you will have the additional oil and fuel systems to deal with.

Remember, just because a pump runs, that doesn’t mean that it will pump or pressurize paint.

Bring back from the dead

It seems that with construction still slow, my customers are bringing in old retired pumps to be fixed.  In the past, these were relegated to the graveyard and new pumps were purchased.  Now, these pumps are being called back into service as fixing them is cheaper than buying new.

So. the lesson here is put up all pumps correctly, even if you think that you may never use them again.  If you don’t throw them out, you may call them back into service or even sell them.  Either way, the 30 min taken will pay dividends.  Also, NEVER seal off the pump by covering the siphon or prime or hose outlet with plastic.  By doing so, you guarantee rust will positively set in.  Clean the machine as well as possible and then pump dry.  I am replacing more rusted parts than worn parts.

Successful secondary income

As I have stated many times before, if you are actively working in a profession that is in any way cyclical, you need a secondary income that is consistent.  If you need an additional $100 to $1000 per month,  the same applies.  This should be from a source that only takes from 1 to 5 hours per week.  With exfuze, that is an incredibly simple thing to accomplish.  With an increase in (consistent) hours, the income will increase considerably.

eXfuze now has a new system for everyone to check out the business and the product at no cost.  Simply click on www.prosperityinpurpose.com/hartsuiker and fill out the information.  Your information will not be “shared” or “sold” to any advertising lists or brokers.  It will just allow you to enter our 3 day challenge system.

When you start the 3 day challenge, you will get a short email from me introducing you to the process.  You will then have access to a site where you can watch and listen to 7 segments that will educate you as to our system.  You will then receive 3 days of eXfuze FOCUS with instructions on it’s benefits.  If you are then interested in the products or the business model, you can choose that option at that point.

The products are unique and unbelievably successful at improving your health.  The business model is simple (you will have just witnessed the entire PIP system) and successful.  I have leads coming in from the PIP system every day. 

You can read more about the products by going to my business websites at www.exfuze.com/hartsuiker or www.extractfuzion.com .

Summer is HERE

OK, the weather that we were looking for is finally here.  We went from a high of 76 to a high of 96 in 2 days.  We are still below the average, but without time to acclimate, is seems much hotter than it really is.

Now is the time to get to the exterior jobs that have been waiting for warm weather.  KEEP bidding though.  Even if you are really busy, bid everything that you are asked to look at.  Interior or exterior, small and large.  Maybe bid the extra/not so attractive jobs a little higher, but bid everything.

The bids from last year that come in, let them know that material costs have risen about 4-5% and you need to cover that increase.  Make sure that any extra work that is due to the passing time and seasons will be extra.  Don’t let the customer drive you to doing extra work for free, when it was their choice to postpone the job.  (unless you like to work for nothing)  If you work cheap once, it will be expected that you will always be willing to work cheap.

Out of Storage

Remember to try any and all of your machines before taking them out on the job to work.  This will save time and frustration.

There are quite a few machines that are being sold that have been stored for years.  Buyer Beware of these.  Many will need work before they can be used successfully.  You cannot just see if they will prime.  You must see if they will build up pressure.

Remember the old adage: “If it seems to be too good to be true, if probably is”.